Phone: 888-830-2219    Fax: 888-830-5126
Aluminum Fence

Material List Help Page
This is how to determine your material list.



    1 - We breakdown the overall example layout listed above, into smaller linear runs, like from point A to point B, and point B to point C and so on. In the example layout, we start at point A with an End Post 2-3" away from the house and go away from the house 10' to point B which is a Gate End Post. In this first 'run', we have 10' of fence, which divided by 6' (the width of the panels) equates to 1.67 panels which is rounded up to 2 because the panels are only shipped in 6' widths. Because there are 2 panels, we will have only 1 Line Post. Line post quantities are equal to the number of panels minus 1.
    So in this first run from A to B, you will have:
    • 1 End Post
    • 2 Fence Panels
    • 1 Line Post
    • 1 Gate Post (these are typically just like End Posts but with a thicker wall. Point K is going to be a Blank Gate Post) Also, all posts come with a flattened pyramid cap standard. You may wish to upgrade to a ball cap.


    2 - In this run, B to C, we have a 4' wide gate which is measured from the inside of the gate post to the inside of the other Gate End Post, point C. Because we already added the first gate post in the previous section, all we have in the second run is:
    • 4 Wide Gate
      gates include self closing hinges and Z-Lock Lockable Latch and can be upgraded to heavier framing or to an Arch Gate.
    • 1 Gate Post

    3 - From C to D which is to the Corner Post, we'll have 9' of fence which equals 1.5 panels (9 divided by 6' wide panel), rounded to 2 Panels and 1 Line Post (2 panels minus 1 = 1 Line Post). So here is this runs total:
    • 1 Line Post
    • 1 Corner Post
    • 2 Fence Panels These panels can be installed in widths of 6' with the other panel cut down to 3' wide or both panels can be cut down to 4.5' to give a more even look. The same is true for the first section of 10'. It could be 6' wide and 4' wide or both cut to 5' wide. Not many, if any, of these runs will work out to be an exact measurement divisible by 6', so some cutting of the panels will be required during the installation process.

    4 - From D to E which is to another Corner Post, the length is 40'. Divided by 6 equals 6.67 panels (40 divided by 6' wide panel), rounded to 7 Panels and 6 Line Posts (7 panels minus 1 = 6 Line Posts). Here is this runs total:
    • 6 Line Posts
    • 1 Corner Post
    • 7 Fence Panels 6 of these panels can be used without any cutting of the panels, but the last one will need to be cut down to 4' wide.

    5 - From E to F which is to a Gate End Post, the length is 42' which is divisible by 6'. This equals 7 panels and 6 Line Posts (7 panels minus 1 = 6 Line Posts). Here is this runs total:
    • 6 Line Posts
    • 1 Gate Post
    • 7 Fence Panels

    6 - From F to G which is to another Gate End Post, the width of the Gate is 3' (again, inside of post to inside of post. This run only has:
    • 1 Gate Post
    • 3' Wide Gate gates include self closing hinges and Z-Lock Lockable Latch and can be upgraded to heavier framing or to an Arch Gate.

    7, 8, & 9 - The next three runs, from G to J can be done the same way as the previous three sections which lead to another Gate End Post.

    10 - This last run, J to K is a 10' wide double gate. It can be two standard gates or two Arches next to one another or one big Arch (Rainbow) across the whole width. Also, as mentioned previously, the final Blank Gate Post has no holes for fence rails to slide into like the End, Line and Corner Posts have. In this final run you would have:
    • 1 Blank Gate Post (the other Gate Post would have been included in the previous run)
    • 10' Wide Double Gate gates include self closing hinges and Z-Lock Lockable Latch and can be upgraded to heavier framing, Arched Gates or a Rainbow Gate.
    • Drop Rod Assembly
Here, we have listed all the posts together to see how they differ: All Posts

To determine if you need to 'STEP' your fence or to follow the grade via 'RACKING', click HERE for more information.

Click here for Installation Instructions.
Copyright © 2007-2013, Aluminum Fences Direct, All Rights Reserved.
No reproduction or copy of designs without written authorization.